COMPUTERISED AUTOMATIC INSTALLATION Mod. CIB MD2-W
According to standards: EN 196-1, EN 1015-11, ISO 679, ASTM C109, C349, C348
The key element for cement laboratories for cement strength calculation
GENERAL CHARACTERISTICS
- Specially designed for serial tests on cement factories or mills and quality control laboratories.
- To be used with: cement mortar, hardened mortar, ceramic, refractories and other similar products.
| Depending on the machine model, following samples could be tested | ||
PRISMATICS 40 x 40,1 x 160 mm, compression & bending, as per EN 196-1, ASTM C348, 349, etc. |
CUBIC 50 mm or 2'' compression, as per ASTM C109. |
CYLINDRICAL 50 mm diam x 50 mm height (cold compression of firebrick specimens).. |
MAIN ADVANTAGES
|
|
TESTING AREA DESCRIPTION
Compact design with one testing frame incorporated The machine is formed by one testing areas placed on the same frame. The hydraulic group and the control computer are located inside the frame, reducing laboratory space requirements.
The monitor, keyboard and printer (optional accessory) are installed on the worktop, at one side of the two testing areas.
COMPRESSION AREA
- Main columns. The tests frame has two columns made in chromium-plated and rectified bar
- Upper crosshead. The upper crosshead is to close the upper part of the testing frame providing a high level rigidity. In its lower part the load cell can be assembles together with the upper compression plate.
- Base plate. The group piston-sleeve is assembled in this piece. The lower plate is assembled over the piston as well as the waste collection tray resulting from the concrete compression tests.
- Piston-sleeve group. The piston finishing is chromium-plated/rectified. The water tightness on the sleeve is guaranteed through a high pressure and low friction joint.
- Compression plates. Two plates are available as compression elements, which are described below:
- Upper plate: The upper plate is assembled through turn on the load cell and will be the transmitter of the force to the mentioned transducer. It is made of hardened steel.
- Lower plate: The lower plate is assembled on the piston and is the one giving the force to the upper plate through the compression device.
- Waste-carrier. It is the dump which serves to collect the material waste once the compression process of a specimen is finished. This dump is placed in the lower part of the compression area, where you can enter through the frame’s frontal door. It is recommended to send to the back area the specimen’s rests with the help of a brush, so that they are poured through the hopper waste from the waste collecting tray to the waste-carrier.
- Protection against projections. The security device is formed by a rotatory transparent screen with an electric security closing, which forbids the equipment’s functioning if the protection screen is opened.
- End of stroke detector. As a security element the machine includes an end of stroke to avoid the piston going out of its guide in an excessive stroke.
CONTROL AND DATA ACQUISITION SYSTEM MD2 |
SOFTWARE, FOR STATIC TEST UNDER WINDOWS, WINTEST.CEM |
|
| - Sampling frequency: 1kHz (1000 readings/sec) - Resolution: 180.000 real points. - Closing loop time: 1 ms. - USB 2.0 connection to PC See particular technical specifications in MD Series Brochure
|
Powerfull configuration and adaptation tools for high demanding users and applications. Any type of test and standard could be configured modifying and introducing the correct parameters. Windows compatible solution, tailored made to work with IBERTEST testing machines & control systems. See particular technical specifications in WINTEST Brochure.
|
TELEDIAGNOSIS SYSTEM
Only for pc controlled IBERTEST machines
Allows a direct links between the machine (any place with pone connection) and the Technical service of IBERTEST.
With this link the Post sale service of IBERTEST could easily diagnose and, most of times correct, the failures detected in the software without the need of a technical displacement.
MODEL COMPARISON: AUTOTEST & CIB SERIES
| Specifications | AUTOTEST 200/10 CIB-200 | AUTOTEST 250/10 CIB-250 | AUTOTEST 400/10 CIB-400 |
|
|---|---|---|---|---|
| Class ISO 7500-1 | 0,5 | |||
| COMPRESSION AREA (AUTOTEST & CIB) |
||||
| Max test load | 200 kN | 250 kN | 400 kN |
|
| Measuring range | 4 to 200kN | 5 to 250 kN | 8 to 400 kN |
|
| Strength measurement | Strain gauge load cell |
|||
| Piston Stroke | 60 mm |
|||
| Columns | 2 | |||
| Free distance between columns | 260 mm |
|||
| Vertical clearance | 250 mm |
|||
| Compression plates diameter | 160 mm |
|||
| BENDING AREA (only AUTOTEST) |
||||
| Max test load | 10 kN |
|||
| Measuring range | 0,2 to 10 kN |
|||
| Strength measurement | Strain gauge load cell | |||
| Piston Stroke | 30 mm. |
|||
| Columns | 2 |
|||
| Vertical clearance | 50 mm. |
|||
| Distance between support rollers | 100 mm |
|||
| Rollers diameter | 10 mm. |
|||
| GENERAL SPECIFICATIONS |
||||
| Dimensions: Testing Frame | 1700 x 785 x 1400 mm. |
|||
| Aprox. Weight | 725 kg. |
|||
| Power | 220/380 V - 50/60 Hz + N + T |
|||
| Safety | Protective door - test stop when door open Emergency Stop: placed in the control |
|||
| NOTE Compression testing frame could be manufactured , on demand, in 300kN version. Bending frame could be manufactured, on demand, in 15, 20 and 30kN versions |
||||
