FEATURED ITEMS
-
EXTENSOMETERS UNTIL SPECIMEN FRACTURE
EXTENSOMETERS UNTIL SPECIMEN FRACTURE
According to standards: Class 0.5 (EN-10.002-4)
To test specimens until break point.
IB/MFL300
Axial extensometer to test specimens until break point, servo-motorised with closed loop control…
in EXTENSOMETRY
Tags: EN_10002_4 read more...
-
UMIB SERIES
SERVOHYDRAULIC STATIC AND QUASISTATIC MATERIALS TESTING MACHINE - UMIB Series
According to standards: UNE-7-474-92 (2), EN-10002-2 (1990), ISO-7500, DIN-51220, 51222, 51223, 51227, 51228 ASTM-E4 (class 1 and grade A/A), BS-1610…
in STEEL TESTING EQUIPMENT
Tags: ISO_7500_1 UNE_7_474_92 BS_1610 EN_10002_2 DIN_51220 ASTM_E4Servohydraulic UMIB Series Brochure
read more...
SERVOHYDRAULIC MACHINE MFIB AND UFIB-1000 FOR FATIGUE BENDING TESTS
According to standards: ISO 7500, PNE 14587
For static and dynamic tests fully automatic, closed loop servo control and computer governed.
|
|
MAIN FRAME
Designed to carry out dynamic bending tests on railways (samples or finished products) using the 
appropriate devices for each application.
MFIB: High stiffness frame, 4 columns, with fixed upper crosshead.
UFIB: High stiffness frame, 4 columns, with mobile upper crosshead. Equipped with hydraulic lateral jaws and fixtures for moving the superior crosshead.
Base in steel,1000x1300 mm, working table provided with 6 grooves (T-shape) for rapid mounting of the testing devices.
On the superior rod, serial mounted with the two points bending punch, is placed the fatigue load cell tension/compression +/- 1000 kN capacity.
The test frame has been designed in order to obtain stiffness higher than 1500 kN/mm, verifying that the security margin, regarding bending, is 4 times higher to the Euler critical load.
SERVOCONTROLLED HYDRAULIC UNIT
- Max work flow: 300 l/min
- Provided with two motor pumps: 150 kW.
- Work at 280 bar of continuous nominal pressure.
- Tank capacityl: 1000 litres.
- Pressure filter: 3 μ, low load lost.
- Return filter 120 μ .
- Filter alarms (2), max oil temperature and
tank level. Additional alarm for over pressures. - Synchronic pump start with unique control
valve, to warrant same work load in both
pumps. - Refrigeration by means of oil/cooled water
system. - High pressure on line accumulator to protect
weak devices of the hydraulic circuit. - Total power: 175 kW aprox.
- Aprox weight: 1.800 kg
SEMI-HIDROSTATIC SERVO CYLINDER
- High response servo valve MOOG with 400 l/m work flow.
- High and low pressure accumulators to improve the response of the system.
- Power: +/-15 Vdc.
- Control signal: +/-10 Vdc.
- Double effect, double shaft and symmetric chambers.
- Small chamber always pressurized.
- Flow volume controlled in the big chamber.
- At 210 bars the max dynamic capacity is 1000 kN.
- Designed for fatigue tests.
- Low friction with hydraulic compensation bearings, joints and permanent lubrication.
- Chromed housing.
- Piston with low friction joints.
- Magnetostrictive position transducer (without contact) placed inside the shaft. SSI protocol, resolution 0,0001 mm.
- Screwed shaft for direct device mounting
FATIGUE LOAD CELL, 1000 kN CAPACITY
|
MAGNETOESTRICTIVE TRANSDUCER
|
CONTROL AND DATA ACQUISITION SYSTEM MD58 |
SOFTWARE, FOR STATIC TEST UNDER WINDOWS, WINTEST.DW |
|
| - Sampling frequency: 5kHz (5000 readings/sec) - Resolution: 180.000 real points. - Closing loop time: 0,2 ms. - USB 2.0 connection to PC See particular technical specifications in MD Series Brochure
|
Powerfull configuration and adaptation tools for high demanding users and applications. Any type of test and standard could be configured modifying and introducing the correct parameters. Windows compatible solution, tailored made to work with IBERTEST materials testing machines & control systems. See particular technical specifications in WINTEST Brochure.
|
TELEDIAGNOSIS SYSTEM
Only for pc controlled IBERTEST materials testing machines
Allows a direct links between the machine (any place with pone connection) and the Technical service of IBERTEST.
With this link the Post sale service of IBERTEST could easily diagnose and, most of times correct, the failures detected in the software without the need of a technical displacement.
SERVOHYDRAULIC MACHINE MFIB AND UFIB-1000 FOR FATIGUE BENDING TESTS
According to standards: ISO 7500, PNE 14587
For static and dynamic tests fully automatic, closed loop servo control and computer governed.
|
|
MAIN FRAME
Designed to carry out dynamic bending tests on railways (samples or finished products) using the appropriate devices for each application.
MFIB: High stiffness frame, 4 columns, with fixed upper crosshead.
UFIB: High stiffness frame, 4 columns, with mobile upper crosshead. Equipped with hydraulic lateral jaws and fixtures for moving the superior crosshead.
Base in steel,1000x1300 mm, working table provided with 6 grooves (T-shape) for rapid mounting of the testing devices.
On the superior rod, serial mounted with the two points bending punch, is placed the fatigue load cell tension/compression +/- 1000 kN capacity.
The test frame has been designed in order to obtain stiffness higher than 1500 kN/mm, verifying that the security margin, regarding bending, is 4 times higher to the Euler critical load.
SERVOCONTROLLED HYDRAULIC UNIT
- Max work flow: 300 l/min
- Provided with two motor pumps: 150 kW.
- Work at 280 bar of continuous nominal pressure.
- Tank capacityl: 1000 litres.
- Pressure filter: 3 μ, low load lost.
- Return filter 120 μ .
- Filter alarms (2), max oil temperature and
tank level. Additional alarm for over pressures. - Synchronic pump start with unique control
valve, to warrant same work load in both
pumps. - Refrigeration by means of oil/cooled water
system. - High pressure on line accumulator to protect
weak devices of the hydraulic circuit. - Total power: 175 kW aprox.
- Aprox weight: 1.800 kg
SEMI-HIDROSTATIC SERVO CYLINDER
- High response servo valve MOOG with 400 l/m work flow.
- High and low pressure accumulators to improve the response of the system.
- Power: +/-15 Vdc.
- Control signal: +/-10 Vdc.
- Double effect, double shaft and symmetric chambers.
- Small chamber always pressurized.
- Flow volume controlled in the big chamber.
- At 210 bars the max dynamic capacity is 1000 kN.
- Designed for fatigue tests.
- Low friction with hydraulic compensation bearings, joints and permanent lubrication.
- Chromed housing.
- Piston with low friction joints.
- Magnetostrictive position transducer (without contact) placed inside the shaft. SSI protocol, resolution 0,0001 mm.
- Screwed shaft for direct device mounting
FATIGUE LOAD CELL, 1000 kN CAPACITY
|
MAGNETOESTRICTIVE TRANSDUCER
|
CONTROL AND DATA ACQUISITION SYSTEM MD58 |
SOFTWARE, FOR STATIC TEST UNDER WINDOWS, WINTEST.DW |
|
| - Sampling frequency: 5kHz (5000 readings/sec) - Resolution: 180.000 real points. - Closing loop time: 0,2 ms. - USB 2.0 connection to PC See particular technical specifications in MD Series Brochure
|
Powerfull configuration and adaptation tools for high demanding users and applications. Any type of test and standard could be configured modifying and introducing the correct parameters. Windows compatible solution, tailored made to work with IBERTEST testing machines & control systems. See particular technical specifications in WINTEST Brochure.
|
TELEDIAGNOSIS SYSTEM
Only for pc controlled IBERTEST machines
Allows a direct links between the machine (any place with pone connection) and the Technical service of IBERTEST.
With this link the Post sale service of IBERTEST could easily diagnose and, most of times correct, the failures detected in the software without the need of a technical displacement.
SERVOHYDRAULIC MACHINE MFIB-2000 FOR STATIC FLEXION TESTS
According to ISO 7500, PNE-14587
- Maximun test load: 2000 kN.
- Control type: Strength or displacement, eligible by the user.
- Accuracy: Class 1 according to ISO 7500.
- Scales: 1 full range.
- Range of Measurement: between 40 and 2000 kN.
- Free distance between columns: 380 x 420 mm.
- Free distance between flexion rollers: 300 mm.
- Supports radio and flexion punches: 60 mm.
- Supports and flexion rollers length: 250 mm.
- Piston stroke: 200 mm.
- Approx. dim: (Wxdxh)2025 x 1100 x 2200.
- Approx. net weight: 4.900 kg.
- For materials testing according to PNE-14587 Standard.
- Servocontrol: strength or displacement, selectable
by the user (adjustable amplitude in kN or mm).
Optional, deformation control
MAIN FRAME MFIB-200
|
|
SERVO CONTROLLER HYDRAULIC GROUP
|
 |
STRAIN GAUGE TRANSDUCER FOR THE LOAD MEASUREMENT
- Output: +/-2 mV/V
- Repeatability: +/-0,05 %
- Non linearity: +/-0,2 %
- Hysteresis: +/-0,2 %
- Zero balance: +/-1,0 %
- Nominal bridge resistance: 350 Ohm
- Temperature compensation between +21and+77ºC
- Working temperature range:-54 to +93 º C
The data obtained is used for two applications: test results and to allow the MD series control system to calculate the kN/sec load speed.
EPROM memory incorporated for safe calibration parameters saving. Even if the machines control fails, these data won’t be lost.
Additional load cells could be installed, to increase the load measuring capacity or for special applications. Anyhow, the 0.5 class is always assured.
SERVOCYLINDERDouble effect, simple shaft and symetric chambers.Main specifications:
ELECTRIC BOARDIn appropriate metallic cupboard, wall mounted. |
MAGNETO STRICTIVE TRANSDUCERS MOD.SSI
|
CONTROL AND DATA ACQUISITION SYSTEM MD2 |
SOFTWARE, FOR STATIC TEST UNDER WINDOWS, WINTEST.MET |
|
| - Sampling frequency: 1kHz (1000 readings/sec) - Resolution: 180.000 real points. - Closing loop time: 1 ms. - USB 2.0 connection to PC See particular technical specifications in MD Series Brochure
|
Powerfull configuration and adaptation tools for high demanding users and applications. Any type of test and standard could be configured modifying and introducing the correct parameters. Windows compatible solution, tailored made to work with IBERTEST materials testing machines & control systems. See particular technical specifications in WINTEST Brochure.
|
TELEDIAGNOSIS SYSTEM
Only for pc controlled IBERTEST materials testing machines
Allows a direct links between the machine (any place with pone connection) and the Technical service of IBERTEST.
With this link the Post sale service of IBERTEST could easily diagnose and, most of times correct, the failures detected in the software without the need of a technical displacement.
Devices designed for materials tests
